Embroidery needles feature sharp points and wider eyes than conventional sewing needles, allowing embroidery threads to pass through.
The needle’s strong ends allow it to pierce densely knit embroidered materials. They are often called crewel needles since they are used chiefly for crewel needlework.
Multiple kinds of fabrics require a type of needle. There are different kinds of hands available for another type of fabric.
The needle size you use is determined by the fabric count of the cloth and the length of the thread you should use. When deciding on needle size, keep in mind that the more significant the short needle should be used.
How To Thread An Embroidery Needle
The annoying thing is to thread a needle before stitching as the thread should pass the small way from the hand, which is a task to be done calmly.
We will discuss some of the ways to thread an embroidery needle.
Step 1: Separating the Strands from the thread
First thing you should know is how to separate the strands of floss. As cotton embroidery floss is the most likely to use thread for embroidering, this thread contains six strands that we can separate.
We need to keep in mind that strands should not get tangled while separating.
First, measure the length of thread you will be using from the Floss. Then, hold the thread with your hand or tweezer, leaving an inch or two above the gripping point. Without leaving the edge, pull the one strand out. Pull it out slowly, avoid tangling the strands. Just pull it out.
Now you’re can to remove each and every strand. This will help you to separate strands from the thread without getting tangled.
To use all six strands combined creates beautiful thick lines and allows you to start stitching straight away. Just be sure you use a wide enough needle and a material with a more delicate weave, or else the cloth may wrinkle and create aggravation.
Also Read – EverSewn Hero-400-Stitch Computerized Embroidery Machine Review
Step 2: Threading Without A Needle Threader
As so many people use to moisturize the end of the thread, hoping that the thread will pass the needle and sometimes that a massive failure because that is not the correct way to thread a needle.
You’ve probably seen the technique of straining while trying to thread through the needle. That, too, can work, but it’s far more complicated. Shift your grasp on the embroidery floss, as shown below, with the string end visible.
Firstly, cut the thread end with sharp scissors to prevent trying with a tangled lot. Hold the thread with your fingers, bring the needle’s eye close to your finger, and try inserting the thread into the needle.
This task will take you a little practice to master. You will need to practice how to face the needle eye in the right direction, and this can be done without relying on good eyesight. If still, this way isn’t working, try applying thread conditioner to thread doe the better result.
Also Read – Rex Industrial Sewing Machine Review
Step 3: Using a Needle Threader
A needle threader is a tool that aids in threading thread through the eye of a needle. There are different types of the needle but the most typical combines a short length of thin wire twisted into a hexagon form with one corner secured by a piece of metal sheet or plastic.
Insert the hook through the needle’s eye and then pass the thread to use the tool. Now you need to pull the pinout of the needle eye. Pull the tool gently to avoid tangling, and try using the needle and thread of similar size.
Step 4: Make use of the built-in needle threader
Even with the most refined illumination, threading a sewing needle may be difficult. However, a built-in needle threader is helpful, which is found on many semis to higher-end sewing machines.
Automated needle threading choices range from a pull-down mechanism that you operate to a drive function that allows the machine to handle all of the work for you.
Also Read – Varmax Sewing Machine Review
Step 5. Place a piece of white behind the needle
Put something white beneath the needle while threading a sewing machine needle. The white cloth with the needle and thread attracts attention to the eye.
Keep a little index card piece fastened to your pin. This keeps the card handy for inserting under the pass through the eye while threading.
Step 6. The thread should be cut at an angle
The thread should be cut at a particular angle that is 45-degree. The cut must be increasingly angled as the thread thickness increases to prevent ripping.
Even if you can’t perceive the tip, guiding the thread into the narrow passages will be much simpler.
Why is it hard to thread a needle?
Most individuals thread a needle by holding an inch or two of thread between their fingers and attempting to guide it into the needle’s eye.
Because the thread is thin and floppy, leading it straight through is challenging. When you fail to make it, the line diverts, requiring you to put it in your mouth to reconstruct the fibers before attempting again.
Are Embroidery Needles and Cross Stitch Needles the Same Thing?
Yes, cross stitch and embroidery needles are different. To work on your project using embroidery or cross-stitch, there are specific and various types of needles available.
Cross stitch needles are spherical with blunt edges and feature a round needle tip. Embroidery needles, on the other hand, possess sharp points. This attribute is essential for cross stitch and embroidery since it contributes to the overall quality.
If the correct size and type have not been chosen, the project’s outcome might differ from the expected results, doesn’t matter your project is cross-stitch or embroidery. You can always have high-quality work by choosing the correct size.
When it concerns cross stitches, a big needle is required to make a slight weave. In contrast, if you are embroidering on a light cloth, you must use a tiny needle